CITIZEN OPOS Driver  Version 1.13.1.5
                                 Release Notes

                                                CITIZEN SYSTEMS JAPAN CO., LTD.
                                                              December 27, 2011

"CTIIZEN OPOS Driver" can develop the application to control the devices by
using "OCX control". 

Please refer to the following manuals when you use it. 

  - CITIZEN OPOS DRIVER 1.13 Setup Guide
  - CITIZEN OPOS DRIVER 1.13 Application Development Guide


The function to detect the completion of printing was added to the driver.
Please refer to "Modification history" for details of this function.
Supported model:
    Model       Firmware Version
  CT-S310II    DT00-0400 or newer
  CT-S601      DL00-2000 or newer
  CT-S651      DM00-2000 or newer
  CT-S801      DH00-2000 or newer
  CT-S851      DK00-2000 or newer
Attention:
  With the older firmware than above, this function doesn't work correctly.
  Please set this function invalidly when you use a printer that is older 
  than these printer. 
  If you use such printer, please disable this function.
  To disable this function, please cancel the setting of "Detect the completion
  of printing" in the configration tool.


--------------------
Modification history
--------------------

Version 1.13.1.5 (Dec 27, 2011)

  [Added functions]
    - Added support for ErrorLevel and ErrorStation property.
    - Improved the sequence to get status when the printer resumes from offline
      to online.


Version 1.13.1.4 (Nov 14, 2011)

  [Fixed problems]
    - Improved the speed when detecting the completion of printing is
      not active.
    - Improved the operation of Log Function.


Version 1.13.1.3 (Oct 7, 2011)

  [Added functions]
    - Added Log Function.

  [Fixed problems]
    - Fixed the problem when some printers are connected simultaneously.
    - In Page Mode, Fixed the problem of BarCode print when the alignment was
      set to PTR_BC_RIGHT.


Version 1.13.1.2 (Aug 19, 2011)

  [Added functions]
    - Added support for GS1 barcode.
        Supported model: CT-S310II/CT-S601/CT-S651/CT-S801/CT-S851
    - Added the function to evade buffer full when the printer error occurred
      in the printing output.
        Supported model: CT-S310II/CT-S601/CT-S651/CT-S801/CT-S851
    - Added the setting of "Detect the completion of printing" in the 
      configration tool.
    - Added the setting of "Detect the completion of printing" and "Write Buffer"
      in the configration tool.
    - Added the file of Release Notes.

  [Fixed problems]
    - Improved the printing of PDF417 barcodes.
    - Fixed the problem when TransactionPrint/PageModePrint/RotatePrint method
      was error.
    - Fixed the problem of the ClearOutput method about the RotatePrint and 
      PageModePrint method.
    - Added support for setting the offset printing of barcode in the page mode.
    - Added support for more serial ports to COM10.
    - Fixed the problem of the access error in parallel connection of CT-S310.
    - Changed the value of the Column/PaperModel setting in registry of the 
      configration tool.
    - Fixed the problem when adding a registered model of "Add Printer" in the
      configration tool.
    - Changed the setting to overwrite when adding a registered same drawer of
      "Add Drawer" in the configration tool.


Version 1.13.1.0 (Apr 18, 2011)

  [Added functions]
    - CT-S310II is added to support.
    - Added the function to detect the completion of printing.
        Supported model: CT-S310II/CT-S601/CT-S651/CT-S801/CT-S851

  [Fixed problems]
    - Fixed it not to keep data after the print of TransactionPrint.
    - Fixed the problem when CheckHealth was executed in the async mode.


Version 1.13.0.0 (Jan 12, 2011)

  New release